|
|
|
|
|
|
|
|
|
INTELCHEM
INDUSTRIES SDN. BHD. (Company No: 246643-P)
PLO 572, Jalan Keluli 10, Kawasan Perindustrian Pasir Gudang
81700 Pasir Gudang, Johor, Malaysia
Tel: 607-252 9000 Fax:607-252 3900 E-mail:
|
|
INCHEM 9 2:01
|
SPECIFICATION SHEET
Doc no: 9201.004
Eff. Date: 1 Nov2006
|
|
FEATURES
A water based putty designed to fill holes, splits and cracks in timber, MDF and other wood related substrates, characterised by its excellent low sink back and non shrink properties. Available in timber tone colours denoted by XXXX.
|
| Bar Room Counter Top |
Bar Room Cabinets & Doors |
Bathroom Vanity Top |
Bathroom Cabinets & Doors |
| Bedroom Furniture |
Chairs |
Internal Handrails |
Trophy Bases |
| Blinds |
Curtain Rods |
Kitchen Bench Top |
Wall Panels/ Wall Units |
| Bookshelves |
Internal Doors |
Kitchen Door & Cabinets |
Moulding |
| Caskets |
Spice Rack |
Tables |
Picture Frame & Skirting |
| CHRACTERISTICS |
| Color Availability: |
1002 Natural, 1010 Rubberwood, 2344 Mahogany, 3269 Teak, 5004 Walnut and Pine
|
| Compatibility: |
Suitable for use under Nitrocellulose, Precatalysed, Acid Catalysed, Polyurethane coatings, Polyester and UV Coatings and Waterborne Coatings.
|
| TECHNICAL DATA |
|
Specific Gravity (@25°C) Thinning Solid Content Stain Compatibility Approx. Drying Time (@ 28°C ,76% humidity) Force Drying SheIfLife@30°C
|
| : |
1.70 ±0.05
|
| : |
Add small amount of water if putty is hard. Stir thoroughly to required consistency. : 80% - 90% (depends on colour)
|
| : |
Water-based or solvent-based stains cannot be mixed with the putty : 1 hour approximate, depending on relative humidity and defect surface area.
Deep holes require long drying times such as overnight. Shallow holes naturally dry faster.
|
| : |
Not recommended due lo potential cracking
|
| : |
12 months (Sufficient stirring may be needed to achieve homogenous product as water phasing may occur 6 months after production date.)
|
| : |
15kg
|
| HEALTH AND SAFETY |
|
This product should be applied in well-ventilated area. Please refer to our Material Safety Data Sheets for detail.
|
| APPLICATION GUIDE |
|
Apply Inchem Putty 92:01 :XXXX by stainless steel spatula on all timber and composite board defects, e.g. holes, cracks, and splits. (Ifnon homogeneity is found in in-can, simply stir the product to achieve uniform texture again.)
|
|
Leave proud of surface to ensure adequate fill is obtained. If defects are deep, fill in two or three applications to avoid cracking of the putty due to stress caused by shrinkage.
|
|
Select putty colour lighter shade than the timber when intending to apply stain as to avoid pronounced repair marks.
|
|
Sand to a smooth finish using PI 80 grade Fre Cut abrasive paper.
|
|
Remove all sanding dust.
|
| STAIN |
| Wiping: |
I8:01:XXXX |
88:01 :XXXX |
|
|
|
| Spraying: |
13:01:XXXX |
I3:02:XXXX |
33:01:XXXX |
93:01:XXXX |
98:0I:XXXX |
| Spray or Wiping: |
13:02:XXXX |
38:01:XXXX |
93:01 :XXXX |
98:01:XXXX |
|
|
|
Select putty colour lighter shade than the stain colour required so as to avoid dark repair marks from being prominent.
|
|
A WOODFILLER Can be applied over open grain timber to fill pores when diluted with small amount of water to form a slurry mixture. Rub well into grain with a circular motion and either remove excess with a damp cloth or allow to dry and sand off with P 180 Free cut paper.
|
FINISHING
Nitrocellulose, Precatalysed, Acid Catalysed, Polyurethane coatings, Polyester and UV Coatings and Waterborne Coatings as per the relevant specification sheets.
|
|
The information given in this Data sheet is given to the best of our ability based on our laboratory results. As we have no control over the quality of substrate used nor the application conditions and methods, we recommend the user to test the product for the purpose required. We are not liable for compensation for any damages arising due to improper use of our products. The information contained herein is subject to change without further notice.
|
|
|
|
